New Products

Signal Conditioner

KSC-2

The KSC-2 is a compact, rugged dual-channel precision amplifier/filter optimized for conditioning Kulite pressure sensors and microphones. It offers fully programmable bi-polar excitation, 6-pole programmable low-pass filtering and precision amplification compatible with any high-speed analog-to-digital converter. The KSC-2 also features an optional REZCOMP™ resonance compensation allowing users to extend the bandwidth of a standard transducer limited by installation, physical construction or physical response of the pressure chip by 2.5 times or more.


For Complete Product Specifications



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


Pressure Scanner

KMPS-4-64 Series
Patent Pending

The KMPS-4-64 is a 64 position pressure scanner with both high accuracy digital and analog outputs. The KMPS-4 electronics module can support up to four KPM-1-16 pressure modules each of which can be a different pressure range and mode. This allows the modules to be placed remotely from the electronics module for ease of installation in tight locations. The RS-485 digital output allows multiple scanners to be read over a single data bus. The Ethernet digital output allows integration into standard networks using TCP or UDP.

The KMPS-4-64 has a trigger input for low latency triggered acquisition. Due to the wide temperature capability it does not require heating or cooling in wind tunnel, flight test and other harsh environments. The pressure transducers are vibration and moisture resistant leading to extreme reliability.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


Pressure Scanner

KMPS-3-64 Series
Patent Pending

The KMPS-3-64 is a 64 position pressure scanner with high accuracy digital output over either an RS-485 or Ethernet bus. There is an internal heater which keeps the internal temperature above freezing to avoid internal icing. An optional motor allows for digital control over the purge mechanism. The KMPS also features auto-zero capabilities. The KMPS-3-64 has a water resistant case ideal for outdoor testing.

The KMPS-3-64 is ideally suited for the flight and ground test market. The Ethernet version features IEEE-1588 timing for precise correlation between multiple devices on the network. The pressure sensors are vibration and moisture resistant leading to extreme reliability. Modules with 16 sensors each are individually replaceable by the user. This allows for different pressure ranges and modes (differential and absolute) in the same scanner.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


Pressure Scanner Module

KPM-1-16 Series
Patent Pending

The KPM-1-16 is a 16 position pressure scanner module. This module mates with any Kulite KMPS Series Pressure Scanner as well as being forward compatible with future pressure scanner chasis from Kulite. The temperature correction coefficients for the 16 on-board sensors are stored in internal memory. This allows for easy mating with any Kulite pressure scanner. Modules with different pressure ranges and modes (differential or absolute) can be attached to the same KMPS Series Pressure Scanner allowing for a multi-range scanner. Modules can be individually replaced allowing for great flexibility during a test and easy replacement between tests.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


Pressure Scanner

KMPS-2-64 Series
Patent Pending

The KMPS-2-64 is a 64 position pressure scanner with high accuracy digital over either an RS-485 or Ethernet bus. There is an internal heater which keeps the internal temperature above freezing to avoid internal icing. An optional motor allows for digital control over the purge mechanism. It also features auto-zero capabilities.

The KMPS-2-64 is ideally suited for the flight test market. The Ethernet version features IEEE-1588 timing for precise correlation between multiple devices on the network. The pressure transducers are vibration and moisture resistant leading to extreme reliability. Plates with 16 sensors each are individually replaceable by the user. This allows for different pressure ranges in the same scanner.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


Pressure Scanner

KMPS-1-64 Series
Patent Pending

The KMPS-1-64 is a 64 position pressure scanner with both high accuracy digital and analog outputs. This allows it to be used with both legacy analog systems and new digital systems. The RS-485 digital output allows multiple scanners to be read over a single data bus. The ethernet digital output allows integration into standard networks using TCP or UDP. It also features purge and auto-zero capabilities.

The KMPS-1-64 has a trigger input for low latency triggered acquisition. Due to the wide temperature capability it does not require heating or cooling in wind tunnel, flight test and other harsh environments. The pressure transducers are vibration and moisture resistant leading to extreme reliability. Plates with 16 sensors each are individually replaceable by the user. This allows for different pressure ranges in the same scanner.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


General Purpose Marine Pressure Transducer

IPTE-230 Series

The application of modern solid state technology to transducer sensing makes the IPTE-230 Series the most advanced general purpose marine pressure transducer. Designed to measure liquid or gas pressure, the transducer is of all-welded stainless steel construction, with an integral pressure port and diaphragm. The IPTE-230 provides an extremely rugged and accurate means for pressure-to-current conversion. The device is hermetically sealed, has no moving parts and requires no maintenance or adjustments. Thus, the IPTE-230 is ideally suited for marine shipboard applications.



Please contact Andrew Schwartz - Manager Marine Applications
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: Andys@kulite.com


Ratiometric Output Pressure Transducer

ETM-435(X)-375(M) Series

The ETM-435(X)-375 is a miniature threaded pressure transducer. The hexagonal head and o-ring seal make it easy to mount and simple to apply.

The ETM-435(X)-375 utilizes a flush metal diaphragm as a force collector. A solid state piezoresistive sensing element is located immediately behind this metal diaphragm which is protected by a metal screen. Force transfer is accomplished via an intervening film of non-compressible silicone oil. This sensing sub assembly is welded to a stainless steel body.



Please contact Josh Lincoln - Senior Sales Engineer for further details
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: Josh@kulite.com


Voltage Output Microprocessor Corrected Pressure Transducer

BME-76-1100 Series

The BME-76-1100 microprocessor corrected transducer offers high accuracy with a total error band of ±0.25% FSO, inclusive of all errors over a wide temperature range of -40°F to +250°F. The ingenious application of modern solid state technology to transducer sensing makes the BME-76-1100 Series the most advanced pressure transducer available. Designed to measure liquid or gas pressure, the transducer is of all-welded stainless steel construction, with integral pressure port and diaphragm.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com


4-20mA Output Microprocessor Corrected Pressure Transducer

BME-76I-1100 Series

The BME-76I-1100 microprocessor corrected transducer offers high accuracy with a total error band of ±0.25% FSO, inclusive of all errors over a wide temperature range of -40°F to +250°F. The ingenious application of modern solid state technology to transducer sensing makes the BME-76I-1100 Series the most advanced pressure transducer available. Designed to measure liquid or gas pressure, the transducer is of all-welded stainless steel construction, with integral pressure port and diaphragm.



Please contact Joseph VanDeWeert - Technical Director Miniature Transducers
Tel: 201-461-0900 · Fax: 201-461-0990 · Email: JoeV@kulite.com